Film Review: Lomography Lady Grey 400 B&W Film Profile

Introduction

Today, we’re going to take a look at Lomography Lady Grey 400 Film, or LOMO_BW_400. This is a high speed B&W film that comes in 35mm roll, and 120 roll. Lomography repackages emulsions from other manufacturers to sell as their own, and research on the internet shows that at one point LOMO_BW_400 was Kodak’s 400TMY2, however, as of mid-late 2017, the emulsion is the same emulsion as Foma’s Fomapan 400. In addition to Fomapan 400, this film is also repackaged as Arista.EDU Ultra 400. This review will serve as a review for all three films as they’re the same emulsion.

Development

There are many ways to develop LOMO_BW_400. If you send your film in here to Simple Film Lab, we develop LOMO_BW_400 with Kodak D-76 mixed at 1:1 for one-shot usage. The development time is 10:00 at 68 degrees Fahrenheit in a Paterson daylight tank with 1 inversion every 15 seconds. We use a 1:4 water:vinegar stop bath between development and fixing. We fix all BW films in Kodak Fixer.

Characteristic Curve

Using Simple Film Lab, here’s the characteristic curve for LOMO_BW_400:

LOMO_BW400_characteristic_curve

The scale along the bottom is exposure EVs, the scale along the left is the measured density as seen by the film scanner. The EV 0 mark is an 18% exposure card exposed correctly via an incident light reading via a Sekonic light meter through a T-Stop rated lens. Every dot along the curve is a full stop of light. As a safety measure, I’ve extended the curve by a couple of stops on both sides of the scale to account for variances in development and scanning, though the film, development process, and scanner is generally very consistent.

Exposure Guidance and Dynamic Range/Exposure Latitude

LOMO_BW_400 has a good amount of dynamic range, though by my estimate, it’s barely a 400 speed film, at least in D-76. You can safely shoot it at ISO 100-400 using the development process described above. The film base plus fog starts to happen most of the way through EV -4 and is fully clear film base by the time we hit EV -6. On the highlight side, it stops getting denser most of the way through EV +10 and doesn’t quite make it to EV +11. This gives a dynamic range of -5 to +10 EVs as a worst case.

For exposure guidance, if developing this film as described above, or if sending it in to be developed by Simple Film Lab, I recommend taking an incident light reading of the darkest part of the scene you want to retain details in and subtracting two stops of exposure from that reading. For example, if the darkest part of the scene that you want to retain detail in reads 1/125 shutter, f/4.0 at ISO 400, either set the shutter to 1/500 or close down the aperture to f/8.0, or a combination of the two to reduce the exposure by two stops.

If you don’t have a light meter, then set your camera exposure compensation to +1 stop, and that will generally result in an acceptable exposure for most situations once scanned in and density corrected.

If you want to add an additional stop of light to the shadows and push the blacks down so that they’re blacker, then you can subtract one stop from the darkest part of the scene you want to capture detail in instead of two stops. LOMO_BW_400 has enough over exposure latitude that this will still result in a good image once scanned in and density corrected for all but the highest contrast scenes.

With that being said, having good blacks requires that the film base plus fog not start to happen until EV -5 at least, so if you want that while shooting this film, then treat it like a 200 speed film and you won’t be disappointed. If you want that dreamy old time film look, then by all means, shoot it at ISO 400 or ISO 800, which will really accentuate the film fog in the blacks.

Resolution/Grain

LOMO_BW_400 has OK resolution for a 400 speed film. Lomography doesn’t publish a spec sheet for it, but Fomapan does for Fomapan 400. At 50% contrast, Fomapan 400 is about 25 line-pairs per mm of film. Putting a 135 format frame up side to side next to 400TX in Adobe Lightroom at 1:1 viewing shows that it doesn’t look to have as much spatial resolution as 400TX (both frames shot through a Sigma 35mm ART prime lens, it’s a really sharp lens). I’d rank it as ever so slightly on the softer side of middle of the road for resolution.

In terms of grain, it’s in 400TX territory as far as grain size is concerned, though 400TX grain is a bit smoother and more pleasant looking than the grain of LOMO_BW_400. In short, in 135 format, the grain is very present but not obnoxious. In medium format 120 roll, it’s significantly less visible but still there. Overall, it has a very film look to it and is quite pleasant.

I personally don’t shoot a lot of LOMO_BW_400 as it’s better suited to candids or street photography and most of what I shoot is studio work with strobes where I go for maximum resolution and/or shoot in 4×5 large format.

Sample Images

This slideshow requires JavaScript.

Here’s a link to a Flickr Album of more images shot on Lomography Lady Grey, Fomapan 400, and Arista.EDU 400. I’ll add more images as I have them available.